Posts Tagged ‘TCC’

How Do You Test a Circuit Breaker with Ground Fault Protection

June 2nd, 2011 2 comments

Over the years MIDWEST has been asked many times how we test circuit breakers that have ground fault protection. High current test sets inject single phase current through one pole, ie phase, of the circuit breaker and the test is timed to see if the breaker trips open within the manufacturer’s specified time, based on the TCC, time current curve.  Whether a GE General Electric circuit breaker, or Cutler Hammer or Square D circuit breaker, molded case circuit breaker or air circuit breaker, the same theory applies to the test procedure. Some electronic overcurrent devices on circuit breakers have a feature allowing you to turn off or defect the ground fault protective function. The manufacturer’s specification sheets should explain this. But, if there is no way to turn off the ground fault protective function on a Westinghouse circuit breaker, for example, a specific test procedure must be followed or the circuit breaker will trip open on ground fault function long before you can put enough current through the breaker to properly test the long time or short time function. Maybe the ground fault pickup range is 100 to 1200 amps and the time delay range is 0.1 to 1.0 seconds.  But your 1600 amp Siemens breaker should be long time tested at 300% or 4800 amps and it will take the breaker 22 seconds to trip at that current level. The procedure is to inject current through one phase, current transformer, and then connect the test set up such that the current returns through a second phase, current transformer, in the opposite direction. The currents will cancel out such that the ground fault pickup sees zero current.  Be sure to test in all three possible combinations. Then each phase is tested for ground fault pickup and delay by just injecting current through that phase. These tests are more time consuming for many molded case circuit breakers.  Always check the manufacturer’s literature if you are not sure how to test a specific circuit breaker. The test requirements may differ between a Federal Pacific circuit breaker and a Westinghouse circuit breaker, for example. But they may also differ between types of circuit breakers by the same manufacturer.  And, of course, always be safe.

Square D MAL361000 Circuit Breaker May Take 5 Minutes 40 Seconds to Trip

January 20th, 2011 Comments off


Square D MAL361000 Circuit Breaker For Sale

Square D MAL361000 Circuit Breaker For Sale

MIDWEST had a customer call because they had an old Square D MAL361000 and it took forever to trip when they had a serious overload problem. He bet it took 3 minutes. This brought up a common misconception concerning how circuit breakers provide protection. When we provide Hands-On Safety Training, this is one of the items we are sure to cover. First of all, whether Square D circuit breakers, Cutler Hammer circuit breakers, GE General Electric circuit breakers, or Siemens circuit breakers, they are not designed to protect people directly. They are designed to protect connected equipment, yet not nuisance trip due to a non harmful transient event. By protecting equipment, circuit breakers consequentially protect people. His old Square D circuit breaker may have taken over 3 minutes to trip and it may have performed the way it was designed. Breakers have a performance specification called a “Time Current Curve,” TCC. In basic terms, whether Westinghouse circuit breakers or ABB circuit breakers, they do not trip immediately at the trip setting. A 1000 amp circuit breaker does not trip right away at 1000 amps or even 1500 or 2000 amps. As a matter of fact, an old 1000 amp Square D MA circuit breaker may have a trip range of 45 seconds to 340 seconds when overloaded with 3000 amps, 300%.  In basic terms, it should not trip in less the 45 seconds and may take as long as 340 seconds to trip. This may seem crazy but, again, it is designed to protect the equipment connected to it while not nuisance tripping. The same breaker would have an instantaneous setting which would determine at what current value the circuit breaker would trip immediately. But, if that setting is over 300%, ie 3000 amps, the breaker would cook for a long time before tripping.  By that time you can smell the breaker overheating.